Wood Router engine Kress 1050-FME-1 with 5.000 – 25.000 U/min


Wood router Kress FME

Kress wood router / Milling engine

1050-FME-1, 1050 Watt ( 1.4 HP ),  5,000-25,000 U/min

Other models are available. Among others with precision collets ER16 or automatic speed control.

 

from 253,47 €

(incl. German VAT)

Kress 1050-FME-1 wood router


Milling Engine Kress 1050-FME-1 with 5,000-25,000 rpm

The milling engine is infinitely variable at 5,000 rpm and is therefore ideally suited for applications in wood, plastic and Plexiglas. At higher speeds in the range of 10,000 rpm, the material would melt, and the routing results would be of poor quality.

Stainless steel clamping neck

The 43H7 stainless steel clamping neck on the router ensures that the bearing seats of the FME are not crushed when the router motor is tightened in the holder on the router, which could lead to overheating of the bearings and the entire spindle.

Very quiet and smooth-running wood router

Compared to other routers, the router motor is extremely silent(e.g. only 74dB at 5,000 rpm). Therefore you can use it for routing work in noise-sensitive areas of a factory or the hobby room without disturbing other occupants or operational processes.

AMB (Kress) carbon brushes

Depending on the AMB milling engine’s care and use, you must replace the carbon brushes after a specific running time. It is advisable to replace both wear brushes directly, as wear occurs typically evenly.

We offer the brushes in a set of 2, which is compatible with all our offered AMB (Kress) models.

The set consists of one carbon without and one carbon with a switch-off device. The replacement carbon with red cable insulation has this shut-off element, which immediately switches off the motor in case of wear and thus forces the carbon’s replacement.

AMB (Kress) carbon brushes

Depending on the AMB milling motor’s care and use, you must replace the carbon brushes after a specific running time. It is advisable to replace both wear brushes directly, as wear occurs typically evenly.

We offer the brushes in a set of 2, which is compatible with all our offered AMB (Kress) models.

The set consists of one carbon without and one carbon with a switch-off device. The replacement carbon with red cable insulation has this shut-off element, which immediately switches off the motor in case of wear and thus forces the carbon’s replacement.

AMB (Kress) millinge engine carbon brushes

Product characteristics AMB (Kress) 1050 FME-1:

  • MAXX-Power engine 1050 watts ( 1.4 HP )
  • Slimmest design for best ergonomics
  • Solid shaft electronic control for constant achievement and number of revolutions
  • Gentle approach and current surge limitation
  • Armoured coil of the engine against dust and particle infestation
  • Steel engine flange with a double stocking for higher milling forces
  • Spindle lock for easy changing of the milling tools
  • Electronic overload protection prevents an overheating of the engine
  • Switching off carbon brush conductors for the protection of the engine
  • To the drive suitably by bending waves
  • Mains cable with patent Quick catch and 4m rubber inlet. In the lengths of 4 and 6 meters as accessories available.

Technical Data:

  • max.1050 Watts ( 1.4 HP )
  • Idling speed 5,000-25,000 1/min.
  • Clamping device 8 mm
  • Clamping neck-Ø 43 mm
  • weight 1,7 kg
  • Super quiet, only 74dB at 5,000 1/min!

Scope of delivery:

  • Kress milling motor 1050-FME-1
  • Precision clamp 8 mm

Available Kress (AMB) milling engine motor models

1050 FME-1 – 1050W – 5.000-25.000 1/min incl. 8mm collet chuck
1050 FME-1 DI – 1050W – 3.500-25.000 1/min

(ready for connection to CNC-STEP Zero3 control)

incl. 8mm collet chuck

Speed adjustable via software, speed control via 0-10 V / 24Volt

incl. connection set for CNC control Zero3
1050 FME-1 DI – 1050W – 3.500-25.000 1/min

(not ready for connection, suitable for external control technology)

incl. 8mm collet chuck


Speed adjustable via software, speed control via 0-10 V / 24Volt


Speed control not ready for connection. Must be configured by the customer according to the conditions.

1050 FME-P – 1050W – 5.000-25.000 1/min – ER16 incl. ER16 collet chuck in 8mm
1050 FME-P DI – 1050W – 3.500-25.000 1/min – ER16

(ready for connection to CNC-STEP Zero3 control)

incl. ER16 collet chuck in 8mm

Speed adjustable via software, speed control via 0-10 V / 24Volt


incl. connection set for CNC control Zero3

1050 FME-P DI – 1050W – 3.500-25.000 1/min – ER16

(not ready for connection, suitable for external control technology)

incl. ER16 collet chuck in 8mm

Speed adjustable via software, speed control via 0-10 V / 24Volt


Speed control not ready for connection. Must be configured by the customer according to the conditions.